Labor Day Sale is LIVE! Save 10% off - AND - up to $500 on Wheels & Tires

More Details

z Search
Cart
z

Search

    z
    z

    Rivian

    Tesla

    Ford

    Porsche / Audi

    Other EVs

    ⛺️ Tents / Racks

    Ford F-150 Lightning EV SnapPlate Instruction Guide

    Ford F-150 Lightning SnapPlate Installation Guide

    Installation and adjustment instructions for the SnapPlate front license plate mount for the 2022–2026 Ford F-150 Lightning.

    Installation

    Step 1

    Test Fit SnapPlate

    Before installing your license plate, test fit SnapPlate on the bumper to determine whether any adjustment is needed. Press both sliders inward and hold them in position.

    Step 2

    Insert SnapPlate

    Insert SnapPlate into the top of the center bumper opening and release both sliders.

    Step 3

    Secure the Sliders

    Pull both sliders outward until they are flush with the vertical bars on the bumper.

    Fit Too Tight? First confirm that SnapPlate is positioned at the top of the bumper opening. If the fit is still too tight, follow the Bumper Depth Adjustment instructions below.
    Step 4 — Optional

    Choose Your Plate Height

    SnapPlate ships in the high position by default. If you prefer a different license plate position, complete the Plate Height Adjustment instructions below before continuing.

    Step 5

    Install Your License Plate

    Attach your license plate using four of the included black or silver Torx security screws.

    Side Trim Current SnapPlate versions have the side trim integrated directly into the plate mount. Separate side trim was used on earlier versions of the product.
    Step 6

    Open the Mount

    Press both sliders inward and hold them in position.

    Step 7

    Install SnapPlate on the Vehicle

    Insert SnapPlate into the top of the center grille opening and release both sliders.

    Step 8

    Fully Engage the Mount

    Pull both sliders outward to make sure SnapPlate is fully secured to the bumper and the magnets are engaged.

    Important Always confirm that both sliders are completely engaged before driving the vehicle.
    Step 9

    Confirm Proper Installation

    Check that the sliders line up with the vertical bars on the grille. This confirms that SnapPlate is secure and the magnets are fully engaged.

    Step 10 — Optional

    Install the Anti-Theft Screws

    For additional security, install the two included black washer-head anti-theft security screws into the holes in the sliders.

    Security Screw Tip If a security screw does not reach, verify that the corresponding slider is completely engaged before tightening the screw.
    Step 11

    Remove Before Automatic Car Washes

    Remove SnapPlate before entering an automated car wash. Most touchless washes may be fine, but removing SnapPlate beforehand is recommended.

    Bumper Depth Adjustment

    If SnapPlate fits too tightly or too loosely against the bumper, the mounting depth can be adjusted for the proper fit.

    Step 1

    Locate the Adjustment Screws

    Locate the T25 Torx adjustment screws on the SnapPlate mounting mechanism.

    Step 2 — Loosen Fit

    Increase the Mounting Depth

    Turn each T25 screw counterclockwise 1/2 turn. Each 1/2-turn adjustment loosens the fit by approximately 0.25 mm. Test fit SnapPlate on the vehicle and repeat in small increments as needed.

    Step 3 — Tighten Fit

    Decrease the Mounting Depth

    Turn each T25 screw clockwise 1/2 turn. Each 1/2-turn adjustment tightens the fit by approximately 0.25 mm. Test fit SnapPlate and repeat in small increments as needed.

    Plate Height Adjustment

    The F-150 Lightning SnapPlate is adjustable into multiple plate positions. SnapPlate ships in the high position by default, which is recommended for maximum airflow to the radiator.

    Step 1

    Remove the Plate Mount

    Remove the two screws securing the license plate mount to the SnapPlate body.

    High Position

    Position the plate mount with the bottom aligned with the SnapPlate body and reinstall the mounting screws.

    Center Position

    Align the middle mounting holes with the middle of the SnapPlate base and reinstall the screws.

    Low Position

    Align the bottom holes of the plate mount with the top holes in the SnapPlate base and reinstall the screws.

    Recommended Position The high position is recommended to provide the best airflow to the F-150 Lightning radiator.
    Final Step

    Install the License Plate

    Attach your license plate using four of the included black or silver security screws.

    Need Installation Help?

    Contact the EV Sportline team for assistance with your Ford F-150 Lightning SnapPlate installation.