Labor Day Sale is LIVE! Save 10% off - AND - up to $500 on Wheels & Tires

More Details

z Search
Cart
z

Search

    z
    z

    Rivian

    Tesla

    Ford

    Porsche / Audi

    Other EVs

    ⛺️ Tents / Racks

    Blazer EV RS & LT SnapPlate Instruction Guide

    Chevrolet Blazer EV SnapPlate Installation Guide

    Installation and adjustment instructions for the SnapPlate front license plate mount for 2024–2026 Chevrolet Blazer EV RS & LT models.

    Installation

    Step 1

    Install Your License Plate

    Attach your license plate to the SnapPlate mount using four of the included T25 Torx security screws.

    Step 2

    Open the SnapPlate

    Locate the OPEN button on the right side of the SnapPlate. Push and hold the OPEN button to release the mounting mechanism.

    Step 3

    Position SnapPlate on the Grille

    Align the center opening in the SnapPlate with the center vertical bar on the Blazer EV grille, then push SnapPlate into the bumper.

    Step 4

    Secure SnapPlate

    Push the CLOSE button on the left side until it sits flush with the SnapPlate body.

    Important SnapPlate must be completely closed before driving. If the mounting mechanism is not fully closed, the magnets are not fully engaged and the SnapPlate could come loose from the vehicle.
    Close Button Difficult to Push? Do not force the mounting mechanism. If the CLOSE button is difficult to push, follow the Grille Depth Adjustment instructions below to loosen the fit.
    Step 5

    Confirm SnapPlate Is Secure

    Double-check that the OPEN button is flush with the SnapPlate body. This confirms that SnapPlate is securely attached.

    Check the Fit If SnapPlate cannot be securely attached or is fully attached but feels loose on the grille, use the Grille Depth Adjustment procedure below to fine-tune the fit.
    Step 6 — Optional

    Install the Anti-Theft Security Screw

    For additional security, use the included T25 security screwdriver to tighten the anti-theft security screw located on the right side of SnapPlate.

    Security Screw Tip If tightening the security screw causes the OPEN button to move, hold the CLOSE button in position while tightening the screw. When removing SnapPlate, the security screw does not need to be completely removed. Simply loosen it until it is flush with the body.

    Grille Depth Adjustment

    The Blazer EV SnapPlate includes two grille-depth adjustment screws. These allow you to fine-tune the mounting mechanism if SnapPlate feels too tight or too loose on the grille.

    Step 1

    Prepare the T10 Driver

    Remove the T10/T25 screwdriver bit from the handle and reinstall it with the smaller T10 bit facing outward.

    Step 2

    Locate the Adjustment Screws

    Locate the two grille-depth adjustment screws on the SnapPlate mounting mechanism. Both screws should be adjusted equally.

    Step 3 — Loosen Fit

    Increase the Grille Depth

    Turn both adjustment screws counterclockwise 1/2 turn. Each 1/2-turn adjustment loosens the fit by approximately 0.25 mm. Test the fit on the vehicle and repeat as necessary.

    Adjustment Limit Repeat the loosening adjustment no more than four times, for a maximum of two full turns. If additional adjustment appears necessary, contact EV Sportline before proceeding.
    Step 4 — Tighten Fit

    Decrease the Grille Depth

    Turn both adjustment screws clockwise 1/2 turn. Each 1/2-turn adjustment tightens the fit by approximately 0.25 mm. Test the fit and repeat as necessary.

    Do Not Overtighten Make adjustments in small increments and take care not to overtighten or strip the adjustment screws.

    Need Installation Help?

    Contact the EV Sportline team for assistance with your Chevrolet Blazer EV SnapPlate installation.